Final rendered model of our windup clock

When approaching modeling this clock, and any other model, I first try to divide it into parts. Obviously every product has its parts, and naturally you would go model one by one. This is that kind of model where your don’t have to think about which part to model first. This is obvious, first you need a clock body, then you can go about modeling which ever part. Here I first created the body, then the back plate with screws, then the front plate without numbers, bells and hammer, legs, and then in the end made the numbers and handles for the front plate.

STEP 1

Ok, in this step we will be creating the body. Since I lost every clock I had like this, I had to model it from reference images from the internet. So, we don’t have the measures, or technical drawings, but we need to model by eye, looking at the various images and approximate the lengths, distances and so on.

I created a template for my default usage with grid extents set to 10. So, make sure you do the same with Snap command, and clicking on the Extents options and input 10.

Now, we can start modeling. Since we don’t know what the accurate dimensions are, we will need to use our old method of trial and error. We will first create three straight lines with Polyline or Line command.

img1

Next thing would be to connect these lines with curves, and that we will do with BlendCrv command. Make sure you use G1 for both ends, so we get tangency.

img2

Using Join command make sure those lines are all joined together. So, next thing would be to create a surface out of this section curve, and we’ll do that with Revolve command. But, before that, we need to turn on the Record History option, so we can work on the surface by simply editing the curve.

img3

Now, if we select our initial curve, and using PointsOn command turn on the control points and if we move those points, we will automatically update the surface as well. If we used Record History that is.

img4

Ok, next thing would be to adjust the curves a bit so the surface is little more accurate. Try to make something like on the image below:

img5

Using OffsetSrf command, we need to offset this surface to inside by 0.3 units. So, make sure you flip the direction normals when in OffsetSrf command, so they point to inside.

img6

Then, simply, with BlendSrf command blend the gaps and Join the four surfaces.

img7

INTRODUCTION

I really liked modeling this model, it turned out really good, and I must say that it was pretty easy to model it too. However, there is fairly enough playing with Osnap, but then again, when do we not use Osnap frequently? Anyway, to get you started, you first need to download some kind of blueprints I made for you out of this model. You just gotta love that Make2D command!!!

Blueprints reference

STEP 1

First things first, we need to setup our blueprints. Not only import them into Rhino, but also position and scale to fit the dimensions marked on them. First, go to Front viewport. You can expand it by double clicking it. Next, using PictureFrame command browse for blueprints you previously saved to your computer. Now, you don’t need to worry about how to position or how big you should make it. We will fix that in a bit, but just make sure your blueprints are not tilted. For that you can use Snap, or even better Ortho.

PictureFrame

Move from blade tip

Scaled blueprints to fit the line length

Another line

pic

INTRODUCTION

Ok, this is another tutorial on modeling some ID product. I’ve tried to simplify this to the bare bone, and I hope I managed to do it. Actually, this is a method you could use on various other projects too. This is what it all comes down to, all you need is create a set of base curves right, after that it is all just music to the ears.

STEP 1 – creating the curves

In the images in this tutorial, you will notice I have 20×20 grid system. You can take a look at my previous tutorial on setting up and prettifying user experience by changing grid and other settings. That will give you an idea how to change your grid system. Basically it is just grid option Extents that is set to 10.

To start off, we will need 4 points. We will use those 4 points for creating a curve. So, go ahead and maximize your Front viewport and create 4 points with x and y coordinates as set: x=-17, y=1 / x=-5, y=-1 / x=9, y=-2 / x=22, y=-1.

create 4 points

Using Curve command, create a curve between those 4 points. To make it easier to snap to the points, just use Osnap option Point. Next, create a line horizontal with start at -17,2 and end at 22,2. We’ll need one more line with start at 7,3 and ending at 8,4. You can create them with Line command or just PolyLine.

two more lines

Next we will create one polyline and one line from Right viewport. Use PolyLine command and for 4 points of polyline use: -4,-5 / -2,-10 / 2,-10 / 4,-5. For the line use PolyLine or Line command and for the start and end use: -5,-8 / 5,-8.

creating some more lines

Using Trim command, just trim off polyline and line, leaving everything above the line. Once you do that, using PointsOn command, you simply show control points of two tilted lines and move the upper control points up by 1 unit.

trim and move control points

In perspective viewport Move (or Copy) that polyline from Mid of the middle (straight) line, and move it to the end point of the first curve we created (22,-1).

moving polyline

Go to Top viewport, and from there create a curve with Curve command (-4,10 / -10,0 / -4,-10).Note, it would be smart to disable Osnap for a second when you are creating this curve. You might get in trouble at middle point if you have some Osnap options on, so to avoid any possible problem, just disable osnap for this step.

just another curve

Move that curve 6 units left. So it just touches the grid. From front viewport move it up by couple of units i.e. 5. Using Rotate command and clicking on the Copy option in command line we will create one more instance of the curve but rotated by 90 degrees. Then, if you haven’t already, enable Osnap, and using Mid option move that curve to the first point of our first curve (-17,1). Use Osnap option Point to snap to that point. Otherwise if you want to input the coordinates, you would have to do it from the same viewport where you created that point, so from Front viewport.

Rotate & copy, move

Ok, this step might get a little confusing, so pay attention. We need to set that curve to face the curve perpendicular. Check the image to see what curves I’m talking about:

what to do

Now, we need to rotate vertical curve so it is perpendicular to the bottom curve. We’ll do that by first creating a line that is perpendicular to the curve below. So, start your beloved PolyLine command, and hover your mouse over the Osnap options, and while holding down CTRL key, you will reveal some more Osnap options. Click on the second one, PerpFrom. Now, you are asked to select the curve on which you would like to show the tracking, so select the lower curve. Now, you can move the tracker where you want to start your line from, and move it all the way to the left (Point Osnap option might help, or end).

PerpFrom osnap option

Now, we created a line that we will use for a rotation angle.

line

Now, just rotate from Front viewport the curve to fit the line angle.

rotation

Now, repeat this step for the other end of the curve and other section polyline:

repeat for this side as well

RESOURCES

STEP 1

We will start from the bottom up. So, first we will model the bottom plate. Create two circles from the top viewport, one 11.9cm in diameter (if you see a diameter option in Circle command, click it so it turns into Radius – that means the diameter is on) and other 11.5cm.

Then we will need three more circles (you can make them anywhere, just make them concentric). Make them 0.3cm, 0.6cm and 0.8cm in diameter.

Now, using Mid, Quad and Cen options in Osnap, position these three little circles on the End (or Quad) point on the outer bigger circle. And move those three from right to left by 0.85cm.

Now we need three more groups of those 3 circles. So, we will use Arraypolar, and array them 4 times around the center of bigger circles (in my case that is 0,0 as I usually have my models in the origin).

Now, select the inner circle of two big, and outer circles of each three-group circles and move those circles up by 0.25cm (from front viewport):

Now, select and copy the inner circle of two bigger, and move it up by 0.55cm

Now, copy the outer circle, and move it up by 0.8cm:

Now, back to those 3-group smaller circles. Select the inner one (4 of them) and move up by 0.75cm. Then, copy those moved circles, and move the copied ones up by 0.2cm.

Now, pick one group of circles, and we’ll start making the boss. Create a surface between two smallest circles. I used extrude, but you can use Loft as well.

Now, the bottom one, I’ve extruded it to the bottom small circle (here, if you want to use loft, you need one more circle that is in the same construction plane as the bottom smaller circle).

And then, extrude the biggest circle to the upper small circle:

Now, we need to create the surfaces between inner and outer circles. We’ll do that with PlanarSrf.

Join those surfaces, and ArrayPolar like we did for the circles.

Now, we’ll make the bottom surface, so select outer circle, and 4 little ones and using PlanarSrf make a surface with 4 holes (just run PlanarSrf command and hit enter):

Repeat the same step for upper 5 circles:

Now, using the Loft command, make a surface out of outer circles (Use the straight sections in style option) :

Join those surfaces, and we’re done with the plate.Theres just one thing to do, that is fillet the edge. So, using FilletEdge and 0.1cm as radius, fillet the shown edge:

Ok, first, sorry for delay, I’ve been meaning to write this one down for 4 days now.

I must say that I’m pretty happy with this one, it turned out very accurate and great. I really like it! And it is pretty easy to model it. So check it out:

RESOURCES

1042008419.jpg

STEP 1

Ok, first things first, so lets start with tubular part. The part where the motor and heater is. I’ve measured 120mm the length and make a line with Polyline or Line command (the length of our reference image is 190mm). We will make three circles two on the start and end of line, and one 30 or 40mm from the left circle. You need to offset them by 2mm, or simply make another circle. I made another circle, so in the end I ended up with 6 circles. Far two right circles are in radius 26 and 28mm. The far left two are 34 and 36mm, and the inner two are 35 and 37mm.

Using InterpCrv command make a line connecting three outer circles. (use Quad option in Osnap for easier snapping). Next, do the same step for 3 inner circles.

Using Sweep2 for first and second rail select outer two circles, and for cross section curve select Curve we made earlier.

Make an ellipse and position it like on the image below:

Next, from Front viewport use Project command to project that ellipse onto our tubular surface. You will get two curves on the surface, and we need only the front one. Using it, we will trim the surface and make a hole:

Now, we’ll move onto handle. I like jumping from one part to another, I guess you already found that out

From top viewport using reference image, outline outer edges with InterpCrv. Just to make sure, I made a straight horizontal line in Top viewport (using Ortho) and trimmed off the two curves. Now, we are sure those two curves has endings in the same cplane.

Create another ellipse, this time one radius 15mm and other 13mm. Using End and Quad options in Osnap, position the ellipse between two curves, first move it to the end of one curve, and using PointsOn command, stretch the ellipse to fit the other curve’s end.

Copy that ellipse, and position it like on the image below. You also need to stretch it with moving control points so it touches both curves. I have also made this ellipse 4 points higher. So, select upper three control points and move them 4 units up, and then move lower three control points and move them by 4 units (mm) down.

Next, using that second bigger ellipsoid and two handle curves, we will make a sweep2.

Using DupBorder we will duplicate border of newly created surface. We will get two closed curves, and we need the little one only, as we already have the bigger one. So, now, delete the surface, and again create sweep2 rail between two rail curves, and using now three closed curves:

And now, we have a handle! Next, we will blend the two surfaces, so use BlendSrf command. Note that we need to check the Same height shapes option:

Hopefully you got something like on the image below:

Resources

Blueprints (required registration, but I think it is worth!)

STEP 1

Again, in this tutorial I have also skipped the blueprints setup.

First, create 3 outline curves in Front viewport with InterpCrv and bridge two upper with one line using polyline (good to have osnap Near option turned on)

Next, split those two bridged curves with that created line (bridge).

Create using InterpCrv outline for the handle section, and offset by 1 inside.

Trim the two curves and split outline curves.

Then, from right viewport, create three lines, and Fillet the corners with 1 unit. Offset that curve by 1 unit inside, and you will create another instance of this curve, but this one won’t have filleted corners.

Extrude those two curves and trim two newly created surfaces with the curves in Front viewport.

The two curves for handle section need to be positioned on the center of your base surfaces. I’ve done that by first creating the surface with Surface from 3 or 4 Corner Points command (SrfPt) and I positioned that surface on the middle of my model. I’ll use that surface for future centerings (I hide it when not needed).

When you moved those two curves to the center, extrude them according to image below:

Here, I’ve used BothSides option in Extrude command. Notice the Top viewport to see the extrusion distance.

Blend the edges of coresponding surfaces, check image below for reference…

Connect blend curves with lines on the mid

Using Network Surface command create surface out of two blend curves and one line.

Do this step for 3 other parts, and join the surfaces. Next, we need to blend the inner and outer surface… I used 0.5 for both sides blend bulge.

In the picture above you can see that I didn’t use blend for connecting the two network surfaces, instead I used Sweep2. Do that 3 more times for other surfaces.

And for the little 3 curved surface corners I used Sweep1:

As you might notice, all these tutorials are pretty much the same. This is the method I use, and find very good. First, make the shape of the model, and then cut the details.

Well, this time we I won’t be showing you how to set the reference images in the background, as I think you have learned that from previous tutorials (I’ll add in tips & tricks section how to insert these, for future reference).

RESOURCES

STEP 1

We’ll make a rough outline trace for the speaker from Front viewport. Using polyline create 4 lines and position them using rotate like on the image below:

Then, using Trim command, trim off the parts we don’t need, so we have a closed curve. Fillet the left upper and lower edges with 12 units (I have set the resource image width to 83 units, just for the aspect ratio reference).

From top viewport, adjust the closed curve so it matches the angle as on the reference background.

Next, from the upper left corner (in top viewport) make a straight line 80 units in length. Using PointsOn turn on the control points for the closed curve, and using RemoveKnot command, remove two outer fillet knots on each round part.

And mirror that closed curve using this straight line’s mid point and Ortho option.

Using these two closed curves, create a surface with Loft command.

Close the objects both left and right sides with planar surface command (PlanarSrf) and join those three surfaces in one object.

Next, we need to make the back side curvy, so lets create a curve with Interpolated points (InterpCrv) like on the image:

Extrude the line (you can use Bothsides option to make sure it goes outside your object). Also, you will probably have to adjust the direction of extrusion, and you can do that by clicking on Direction option of Extrude command.

Trim off the parts of both extruded surface, and that object. After that, join the object.

Now, we will create a curve for splitting the base model. We are using the same method as for creating the rough outline trace as on the beginning of this tutorial…

We do this step again for top curve:

Using filletedge command fillet the two edges where our new curvy surface touches the flat surfaces.

From frot viewport, project the curve on the base model. You should get this:

Do the same for the top curve, but Project the curve on the object from Top viewport.

Copy the main object with Copy command, and paste it with Paste command (CTRL+C and CTRL+V works here). It is better to first copy, then trim the base object with one (either top or front curve) then paste that copied object and do the trimming with other (if you first trimmed with front curve, then now trim with top curve) curve.

Using earlier projected curves we will create cross sections between them with polyline command.

Mid and Perp options in Osnap toolbar are very helpful here. Near option is also needed here. Proceed with creating cross section lines until you get something like this (please not those lines need to be perpendicular to the curves).

Using sweep 2 rails (sweep2) command and set the yellow two curves from upper image as two rails, and other lines as cross sections. And tick the Closed Sweep option.

Unhide all the other parts, and join this surface with other two.

Now, you can explode that as we will be offsetting (offsetsrf – I have offset by 0.5 units) the main two surfaces and we’ll again create the cross section…

Using Duplicate border on the offset surfaces create the rail curves.

This is the same way of creating the object as few steps before, but this one is by 0.5 units smaller. I believe we could simply scale down the bigger part, but hey, this is me, and I’m making this…

Ok, so we made an alternative to non-existing shell command in Rhino3D v4 (rumor is that in v5 there will be shell command-yey!).