Final model

STEP 1

First things first. Make sure you got your Snap option turned on in the status bar, and your OSnap enabled with some of the most commonly used options like End, Near, Point, Mid and Int.

We’ll start creating this little shovel from top viewport, like we would start tracing an image of some existing shovel imported in Rhinoceros.

With Curve command, create a curve in Top viewport which has its control points exactly like on the image below. This is why Snap (to grid) is handy tool to use here.

Image 1

Then we need another copy of this curve, and for that we will use Mirror command and mirror it across x axis.After that, use Join command to join two curves.

Then we can either use Line command to close these two curves into one closed polyline/polycurve, or use Close command which will do the same thing with less clicks.

Image 2

Now, using Rectangle command we will create a rectangle like on the image below: do not worry about the dimensions, just count the grid boxes and you’ll be fine. I’ve got some dimensions for you in case you get lost

Image 3

With Trim command, we will trim the parts of the two closed polylines which will help us join all curves into one closed:

Image 4

Next thing would be to make the corners smoother. They aren’t normally that sharp, are they? So, using Fillet command we need to fillet the upper and lower corners with 1 unit, and the inner ones with 2 units, and the tip of the shovel with 0.4 units:

Image 5

Now, before we go any further, it is good to check if all these lines and curves are joined all together. Just click anywhere on the line, and if everything is ok then it will be yellow as selected. One more thing to check is if this IS really closed curve with SelClosedCrv command which will select all closed curves.

Next thing we need is a basic shape of our shovel. Since it is curved in two sides, the best basic shape would be an ellipsoid. Using Ellipsoid command create one positioned just like on the image below:

Image 6

Ok, now we will Cut the Ellipsoid with the closed curve we created. From Top viewport, we need to select both Ellipsoid and closed curve, and run Project command. It is important to do this in Front viewport because the viewport is controlling the direction of the projection.

Image 7

Now we got two projected curves. One on the top and one on the bottom of ellipsoid. We don’t need the upper one, and we can delete it by selecting it and hitting Delete key on keyboard.

Using Split command, we will first select the object we want to cut which is in this case ellipsoid, and then the curve which is the object we wish to split with:

Image 8

Now we have finally created something that is actually resembling our shovel. This is one thin surface, and we need some thickness. Using OffsetSrf command we will first offset the surface and create one on top with distance of 0.3 units: (when you start the command, it will display white arrows on your surface, those are normals, and are used to see in which direction the offset will occur. Chances are your arrows point towards bottom, click on the surface and the arrows will change direction)

Image 9

We now have two flat surfaces and we need to connect them somehow. We’ll do that with BlendSrf command which will basically create nice blend surface between two surfaces: (Use AutoConnect option in command line)

Image 10

With Join command join the blend surface with two flat surfaces. You will notice on the part where would handle start there is some weird hole. Never mind that, that part will soon disappear.

Again, we need to create another Ellipsoid. Using Ellipsoid command create one like on the image below. Again, the positioning and size is crucial here.

Image 11

Hint: When you start Ellipsoid command, just follow these steps. Input “10, -3.75″ (that will set the center in the right position), press enter while active Front viewport (click anywhere in the viewport), “6, -3.75″ (that will set one dimension of the ellipsoid – length), press enter while still in Front viewport, “10, -2.25″, press enter while in Front viewport, “10,-1.5″ press enter Top viewport is active. Do not input apostrophe signs.

Using ExtractIsoCurve command, create a extract isocurve from the middle of ellipsoid. You need to hit the Quad point to make sure the circle is in ellipsoid’s center.

Image 12

Using ExtrudeCrv command we will create a cylinder out of this circle. So, start the command, select the circle, make sure the Cap option is set to Yes, and input 15 units in command line as extrusion distance.

Image 13

With BooleanUnion command connect ellipsoid with cylinder:

Image 14

Again, with BooleanUnion command we need to connect the plate and handle part:

Image 15

If you are getting something like on the image below….

Image 16

… then you need to use Dir command on the plate before you use BooleanUnion. Because the normals are pointing towards the inside, while they should point towards outside.

This next part will be a bit tricky, so pay attention. We need to create a variable fillet on the edges that connect the handle part and the shovel plate. The biggest radius will be 1 unit, while all others will be 0.8 units.

So, start FilletEdge command, and set 0.08 as default radius. Select the edges:

Image 17

… press enter, and click on AddHandle option in command line. Add 7 more handles like on the image below:

Image 18

The two big ones show be set to 1 unit, and you do that by clicking on the outer dot (center of an arc) and inputing the values.

Image 19

Final rendered model of our windup clock

When approaching modeling this clock, and any other model, I first try to divide it into parts. Obviously every product has its parts, and naturally you would go model one by one. This is that kind of model where your don’t have to think about which part to model first. This is obvious, first you need a clock body, then you can go about modeling which ever part. Here I first created the body, then the back plate with screws, then the front plate without numbers, bells and hammer, legs, and then in the end made the numbers and handles for the front plate.

STEP 1

Ok, in this step we will be creating the body. Since I lost every clock I had like this, I had to model it from reference images from the internet. So, we don’t have the measures, or technical drawings, but we need to model by eye, looking at the various images and approximate the lengths, distances and so on.

I created a template for my default usage with grid extents set to 10. So, make sure you do the same with Snap command, and clicking on the Extents options and input 10.

Now, we can start modeling. Since we don’t know what the accurate dimensions are, we will need to use our old method of trial and error. We will first create three straight lines with Polyline or Line command.

img1

Next thing would be to connect these lines with curves, and that we will do with BlendCrv command. Make sure you use G1 for both ends, so we get tangency.

img2

Using Join command make sure those lines are all joined together. So, next thing would be to create a surface out of this section curve, and we’ll do that with Revolve command. But, before that, we need to turn on the Record History option, so we can work on the surface by simply editing the curve.

img3

Now, if we select our initial curve, and using PointsOn command turn on the control points and if we move those points, we will automatically update the surface as well. If we used Record History that is.

img4

Ok, next thing would be to adjust the curves a bit so the surface is little more accurate. Try to make something like on the image below:

img5

Using OffsetSrf command, we need to offset this surface to inside by 0.3 units. So, make sure you flip the direction normals when in OffsetSrf command, so they point to inside.

img6

Then, simply, with BlendSrf command blend the gaps and Join the four surfaces.

img7

Final scene

Since it that time in the year again, some of you might find it useful to learn how to create few Christmas decorations for your tree visualisations

Introduction

Well, basically what we will do here is use solids for basic shapes and cut them how we like it.Simple, eh?

Step 1

In this step we will be creating the simplest decoration.

First Decoration

Go ahead, and create a sphere using Sphere command. Center it in the origin (0,0) and use 10 units as radius. To make this even simpler, you can set your Grid options like I have them. Just run Grid command, and where it says Extents click on it and input 10. That way you will have 10 units in your grid in every direction in the viewport which was active when you run the command. To apply this setting to all viewports, just use ApplyTo setting in Grid command. Click on it so it toggles from ActiveViewport to AllViewports. Now, simply using Snap option in your status bar we will start creating this Sphere.

Image 1

Once you got your Sphere, create another one, using 7 units as radius and position its center on 8,0. That is, 8 on the x axis, and 0 on the y axis.

Image 2

Now, using BooleanDifference make a hole in the bigger Sphere.

Image 3

We need to fillet the edges of this sphere. Using FilletEdge command fillet the edge with 0.2 as radius.

Image 4

Create a Circle from Top viewport with 5.5 as radius.

Image 5

We will Project this Circle onto the Sphere. We need to do this from Top viewport. So make sure it is active, and run the Project command to do the projection of the Circle on the Sphere. You will get 3 projected curves, and we only need the top one, so you can delete other two:

Image 6

Using Split or Trim command, we need to trim the upper part of the Sphere, with projected circle.

Image 7

Next thing we need is another Circle. This time create a Circle with 1.5 units as radius. Create it from top viewport in the origin (0,0). Then you will need to move it up (from either front or right viewport) with Move command by 17 units.

Image 8

Now, using ExtrudeCrv extrude this circle up by 1 unit. Make sure you don’t have Cap set to Yes, or BothSides set to Yes. Those two options need to be set to No.

Image 9

Ok, once you’ve done this, you need to make a surface with smooth transition from the sphere to the extruded circle. You will use BlendSrf command to do just that. As for the BlendSrf options, just leave it at default settings. Meaning AutoChain set to No, and for the Blend Bulge leave it as well at default settings, which are 1,1 and all other options unchecked.

Image 10

Next we will create a cap and a little wire to hang our decoration somewhere. So, using OffsetSrf offset the little cylinder surface outwards by 0.1 units.

Image 11

Now, using ExtendSrf command we will extend the upper edge of the offset surface up by 0.1

Image 12

Using Cap command we will close this surface into solid.

Image 13

Create another Circle, from Top viewport and use 0.5 units as radius. You should get your circle like on the image below:

Image 14

Now, using ExtrudeCrv command set the Cap setting to Yes, and extrude it up by 20 units, just so it goes through the cap:

Image 15

Using BooleanDifference command make a hole with this cylinder in the cap:

Image 16

Using FilletEdge fillet the edges of the tip with 0.1 as radius:

Image 17

Create another Circle with 2 units as radius, and position it like on the image below. Just make sure you create your circle from Front viewport. You can start Circle command, input in the command line when it asks you for the center 0,20 for the center, and then just 2 for the radius. You should get exactly the curve like on the image:

Image 18

We need a Curve starting from the circle. Using InterpCrv command we will create such curve from Front viewport: (you can start using OSnap if you haven’t already – Near would come in handy here)

Image 19

Using Mirror command we need to mirror this curve to the other side.

Image 20

Using Trim command we need to trim the Circle:

Image 21

I have almost perfectly hit the curve direction and smoothness and actually the curve is visually tangent to the circle. In reality that isn’t the case, so we need to fix it. We will match our curve onto the circle with Match command:

Image 22

Here you can see the black curve on the left, this is how the curve will be adjusted to match the tangency. So, now you see I didn’t actually hit the tangency manually. Do this same step for the right curve as well, and join all three into one:

Image 23

If necessary, using PointsOn you can change your curve a bit. But you will see if this is necessary after you make a surface. Using Pipe command we need to create a pipe surface. Use 0.2 as radius:

Image 24

Here you see this needs some adjustments. So, first, try moving it up a bit to see if this can fix it. If not, using PointsOn you will need to adjust the curve itself.

Image 25

For the purposes of this course, just moving this wire will do.

Introduction

Final rendered model

Ok, the above image shows what would your final model look like rendered.

So, how will we approach modeling this stool? You must be asking yourselves where should you start? Well, it doesn’t matter where you start. If you prefer tackling “harder” parts first, then it is your way of starting. However if you like to start with easier, more “solids” objects (like spheres, boxes, cylinders etc.) then you might want to start with the base and leg first. But I like to throw myself in a project head on first. So, I would go with the seat frame first then move to the wooden seat part, then go to the leg base, and then the leg.

So. lets start with the seat frame. How are we going to do that? Well, using Sweep1 command. For that we need one rail curve, and one section curve. What Sweep1 command does, it basically “drives” the section curve along the rail curve, and by that it makes a surface.

Lets start.

STEP 1

From your Right viewport, we will start creating straight lines. For that we will be using PolyLine command, and for extra help on creating we will turn on Snap and Ortho options from the Status bar of our Rhino window.

We need one PolyLine which will be made out of two lines:

Image 1

Ok, in the image above you can see our PolyLine. What I did is started from the Origin (the place where y-axis green line meets x-axis red line). So, we turned on the Snap option so we can easily snap to the origin. Starting our PolyLine from there, I then input in the command line the number which will be the length of the first part of our PolyLine. So, I typed in 2.7 and confirmed it with Enter key. After that you can see that your line in viewport is now exactly 2.7 units long, and you can set the direction in which it will go. Now, our Ortho option comes in handy because we want this line to be straight along x-axis. After you aimed it, just click so you confirm the other end of first part of PolyLine. Next, we need one line 3.5 units long, and going along y-axis. You need to do all this while still in PolyLine command.

Then, you will need a small line 0.8 units long and under certain angle of 60 degrees. We will start again our PolyLine (or in this case it is enough to use just Line) command and start our line from the origin, and inputting in commandline a number 0.8 and confirming it with enter key we will lock the line’s length, and after that you just input in the commandline <60 and confirm it with enter key. This way you will have locked both length and angle you need that line to be made.

Image 2

Ok, when you’ve done that, we now need to “smooth” the transitions between the line parts. We want them to be rounded under certain radius, and we will do that with Fillet command. So, go ahead and start the Fillet command, and use 0.5 units as radius. You need to click on the two ends of two matching lines. You should have something like on the image below:

Image 3

After filleting the corners, we need to Join all the curves into one open curve. Just selecting all (CTRL+A) and running Join command will do just that.

Now, we need the same set of curves on the other side, and the distance between those two will be 2.75 units. So, using Copy command we will copy that line exactly by 2.75 units to the right (working from Front viewport) by inputting the 2.75 and confirming it with enter key. That way we are locking the Copy distance on 2.75.

Image 4

Ok, now we need to use some OSnap. If you aren’t familiar with it, you should check out OSnap introduction. Using End OSnap option, we will snap to both ends of two curves and create a Line between them:

Image 5

Now we need to Fillet the corners between our newly created two lines and two curves. The radii are the same as before:

Image 6

Now, again, using Join command join all the cruves and lines into one closed curve. And there you go, we made one very nice and accurate rail which we will be using to create a seat frame in just few moments.

Before that we need to create a section curve.

We’ll do that with Rectangle command from Right viewport. Make sure once you start Rectangle command you click on the Rounded option in the command line. That way after creating the rectangle the command will ask us to input the corner radius for all four corners. So, for the first corner we will input 0.25 units, and for the other 0.1 units. For the corner radius we need to input 0.02. Then you should get something like on the image below:

Image 7

Ok, you noticed we created this Rectangle in god knows what position. No fear, we just need to move it  a bit with Move command. In this moving process, we will use OSnap option Mid as it will come in handy because we need to move that rectangle from its midpoint to the midpoint on the closed rail curve.

Image 8

Ok, now we have both our rail curve, and section curve. And now we can go ahead and create a surface out of the two. Using Sweep1 command we will do just that. For the Sweep1 option, leave it as it is:

Image 9

Great, we got our seat frame surface. Moving on to the seat surface. For that we also need a set of curves, as you already figured that out for yourselves, for each surface creation we need curves. But, in this case, we won’t be creating new set of curves, but rather using the existing ones.

Now would be a great idea to move this frame surface into another layer and hide that layer. Lets go create a new layer and name it “Seat Frame”. Now, select the frame surface, and right click on the “Seat Frame” layer, and select Change Object Layer. Now our surface is in this layer. We can easily lock or hide the layer by clicking on the little yellow bulb so it becomes blue (turned off).

Image 10

Image 11

INTRODUCTION

Ok, this is another tutorial on modeling some ID product. I’ve tried to simplify this to the bare bone, and I hope I managed to do it. Actually, this is a method you could use on various other projects too. This is what it all comes down to, all you need is create a set of base curves right, after that it is all just music to the ears.

STEP 1 – creating the curves

In the images in this tutorial, you will notice I have 20×20 grid system. You can take a look at my previous tutorial on setting up and prettifying user experience by changing grid and other settings. That will give you an idea how to change your grid system. Basically it is just grid option Extents that is set to 10.

To start off, we will need 4 points. We will use those 4 points for creating a curve. So, go ahead and maximize your Front viewport and create 4 points with x and y coordinates as set: x=-17, y=1 / x=-5, y=-1 / x=9, y=-2 / x=22, y=-1.

create 4 points

Using Curve command, create a curve between those 4 points. To make it easier to snap to the points, just use Osnap option Point. Next, create a line horizontal with start at -17,2 and end at 22,2. We’ll need one more line with start at 7,3 and ending at 8,4. You can create them with Line command or just PolyLine.

two more lines

Next we will create one polyline and one line from Right viewport. Use PolyLine command and for 4 points of polyline use: -4,-5 / -2,-10 / 2,-10 / 4,-5. For the line use PolyLine or Line command and for the start and end use: -5,-8 / 5,-8.

creating some more lines

Using Trim command, just trim off polyline and line, leaving everything above the line. Once you do that, using PointsOn command, you simply show control points of two tilted lines and move the upper control points up by 1 unit.

trim and move control points

In perspective viewport Move (or Copy) that polyline from Mid of the middle (straight) line, and move it to the end point of the first curve we created (22,-1).

moving polyline

Go to Top viewport, and from there create a curve with Curve command (-4,10 / -10,0 / -4,-10).Note, it would be smart to disable Osnap for a second when you are creating this curve. You might get in trouble at middle point if you have some Osnap options on, so to avoid any possible problem, just disable osnap for this step.

just another curve

Move that curve 6 units left. So it just touches the grid. From front viewport move it up by couple of units i.e. 5. Using Rotate command and clicking on the Copy option in command line we will create one more instance of the curve but rotated by 90 degrees. Then, if you haven’t already, enable Osnap, and using Mid option move that curve to the first point of our first curve (-17,1). Use Osnap option Point to snap to that point. Otherwise if you want to input the coordinates, you would have to do it from the same viewport where you created that point, so from Front viewport.

Rotate & copy, move

Ok, this step might get a little confusing, so pay attention. We need to set that curve to face the curve perpendicular. Check the image to see what curves I’m talking about:

what to do

Now, we need to rotate vertical curve so it is perpendicular to the bottom curve. We’ll do that by first creating a line that is perpendicular to the curve below. So, start your beloved PolyLine command, and hover your mouse over the Osnap options, and while holding down CTRL key, you will reveal some more Osnap options. Click on the second one, PerpFrom. Now, you are asked to select the curve on which you would like to show the tracking, so select the lower curve. Now, you can move the tracker where you want to start your line from, and move it all the way to the left (Point Osnap option might help, or end).

PerpFrom osnap option

Now, we created a line that we will use for a rotation angle.

line

Now, just rotate from Front viewport the curve to fit the line angle.

rotation

Now, repeat this step for the other end of the curve and other section polyline:

repeat for this side as well

Ok, first, sorry for delay, I’ve been meaning to write this one down for 4 days now.

I must say that I’m pretty happy with this one, it turned out very accurate and great. I really like it! And it is pretty easy to model it. So check it out:

RESOURCES

1042008419.jpg

STEP 1

Ok, first things first, so lets start with tubular part. The part where the motor and heater is. I’ve measured 120mm the length and make a line with Polyline or Line command (the length of our reference image is 190mm). We will make three circles two on the start and end of line, and one 30 or 40mm from the left circle. You need to offset them by 2mm, or simply make another circle. I made another circle, so in the end I ended up with 6 circles. Far two right circles are in radius 26 and 28mm. The far left two are 34 and 36mm, and the inner two are 35 and 37mm.

Using InterpCrv command make a line connecting three outer circles. (use Quad option in Osnap for easier snapping). Next, do the same step for 3 inner circles.

Using Sweep2 for first and second rail select outer two circles, and for cross section curve select Curve we made earlier.

Make an ellipse and position it like on the image below:

Next, from Front viewport use Project command to project that ellipse onto our tubular surface. You will get two curves on the surface, and we need only the front one. Using it, we will trim the surface and make a hole:

Now, we’ll move onto handle. I like jumping from one part to another, I guess you already found that out

From top viewport using reference image, outline outer edges with InterpCrv. Just to make sure, I made a straight horizontal line in Top viewport (using Ortho) and trimmed off the two curves. Now, we are sure those two curves has endings in the same cplane.

Create another ellipse, this time one radius 15mm and other 13mm. Using End and Quad options in Osnap, position the ellipse between two curves, first move it to the end of one curve, and using PointsOn command, stretch the ellipse to fit the other curve’s end.

Copy that ellipse, and position it like on the image below. You also need to stretch it with moving control points so it touches both curves. I have also made this ellipse 4 points higher. So, select upper three control points and move them 4 units up, and then move lower three control points and move them by 4 units (mm) down.

Next, using that second bigger ellipsoid and two handle curves, we will make a sweep2.

Using DupBorder we will duplicate border of newly created surface. We will get two closed curves, and we need the little one only, as we already have the bigger one. So, now, delete the surface, and again create sweep2 rail between two rail curves, and using now three closed curves:

And now, we have a handle! Next, we will blend the two surfaces, so use BlendSrf command. Note that we need to check the Same height shapes option:

Hopefully you got something like on the image below:

As you might notice, all these tutorials are pretty much the same. This is the method I use, and find very good. First, make the shape of the model, and then cut the details.

Well, this time we I won’t be showing you how to set the reference images in the background, as I think you have learned that from previous tutorials (I’ll add in tips & tricks section how to insert these, for future reference).

RESOURCES

STEP 1

We’ll make a rough outline trace for the speaker from Front viewport. Using polyline create 4 lines and position them using rotate like on the image below:

Then, using Trim command, trim off the parts we don’t need, so we have a closed curve. Fillet the left upper and lower edges with 12 units (I have set the resource image width to 83 units, just for the aspect ratio reference).

From top viewport, adjust the closed curve so it matches the angle as on the reference background.

Next, from the upper left corner (in top viewport) make a straight line 80 units in length. Using PointsOn turn on the control points for the closed curve, and using RemoveKnot command, remove two outer fillet knots on each round part.

And mirror that closed curve using this straight line’s mid point and Ortho option.

Using these two closed curves, create a surface with Loft command.

Close the objects both left and right sides with planar surface command (PlanarSrf) and join those three surfaces in one object.

Next, we need to make the back side curvy, so lets create a curve with Interpolated points (InterpCrv) like on the image:

Extrude the line (you can use Bothsides option to make sure it goes outside your object). Also, you will probably have to adjust the direction of extrusion, and you can do that by clicking on Direction option of Extrude command.

Trim off the parts of both extruded surface, and that object. After that, join the object.

Now, we will create a curve for splitting the base model. We are using the same method as for creating the rough outline trace as on the beginning of this tutorial…

We do this step again for top curve:

Using filletedge command fillet the two edges where our new curvy surface touches the flat surfaces.

From frot viewport, project the curve on the base model. You should get this:

Do the same for the top curve, but Project the curve on the object from Top viewport.

Copy the main object with Copy command, and paste it with Paste command (CTRL+C and CTRL+V works here). It is better to first copy, then trim the base object with one (either top or front curve) then paste that copied object and do the trimming with other (if you first trimmed with front curve, then now trim with top curve) curve.

Using earlier projected curves we will create cross sections between them with polyline command.

Mid and Perp options in Osnap toolbar are very helpful here. Near option is also needed here. Proceed with creating cross section lines until you get something like this (please not those lines need to be perpendicular to the curves).

Using sweep 2 rails (sweep2) command and set the yellow two curves from upper image as two rails, and other lines as cross sections. And tick the Closed Sweep option.

Unhide all the other parts, and join this surface with other two.

Now, you can explode that as we will be offsetting (offsetsrf – I have offset by 0.5 units) the main two surfaces and we’ll again create the cross section…

Using Duplicate border on the offset surfaces create the rail curves.

This is the same way of creating the object as few steps before, but this one is by 0.5 units smaller. I believe we could simply scale down the bigger part, but hey, this is me, and I’m making this…

Ok, so we made an alternative to non-existing shell command in Rhino3D v4 (rumor is that in v5 there will be shell command-yey!).