Final model

STEP 1

First things first. Make sure you got your Snap option turned on in the status bar, and your OSnap enabled with some of the most commonly used options like End, Near, Point, Mid and Int.

We’ll start creating this little shovel from top viewport, like we would start tracing an image of some existing shovel imported in Rhinoceros.

With Curve command, create a curve in Top viewport which has its control points exactly like on the image below. This is why Snap (to grid) is handy tool to use here.

Image 1

Then we need another copy of this curve, and for that we will use Mirror command and mirror it across x axis.After that, use Join command to join two curves.

Then we can either use Line command to close these two curves into one closed polyline/polycurve, or use Close command which will do the same thing with less clicks.

Image 2

Now, using Rectangle command we will create a rectangle like on the image below: do not worry about the dimensions, just count the grid boxes and you’ll be fine. I’ve got some dimensions for you in case you get lost

Image 3

With Trim command, we will trim the parts of the two closed polylines which will help us join all curves into one closed:

Image 4

Next thing would be to make the corners smoother. They aren’t normally that sharp, are they? So, using Fillet command we need to fillet the upper and lower corners with 1 unit, and the inner ones with 2 units, and the tip of the shovel with 0.4 units:

Image 5

Now, before we go any further, it is good to check if all these lines and curves are joined all together. Just click anywhere on the line, and if everything is ok then it will be yellow as selected. One more thing to check is if this IS really closed curve with SelClosedCrv command which will select all closed curves.

Next thing we need is a basic shape of our shovel. Since it is curved in two sides, the best basic shape would be an ellipsoid. Using Ellipsoid command create one positioned just like on the image below:

Image 6

Ok, now we will Cut the Ellipsoid with the closed curve we created. From Top viewport, we need to select both Ellipsoid and closed curve, and run Project command. It is important to do this in Front viewport because the viewport is controlling the direction of the projection.

Image 7

Now we got two projected curves. One on the top and one on the bottom of ellipsoid. We don’t need the upper one, and we can delete it by selecting it and hitting Delete key on keyboard.

Using Split command, we will first select the object we want to cut which is in this case ellipsoid, and then the curve which is the object we wish to split with:

Image 8

Now we have finally created something that is actually resembling our shovel. This is one thin surface, and we need some thickness. Using OffsetSrf command we will first offset the surface and create one on top with distance of 0.3 units: (when you start the command, it will display white arrows on your surface, those are normals, and are used to see in which direction the offset will occur. Chances are your arrows point towards bottom, click on the surface and the arrows will change direction)

Image 9

We now have two flat surfaces and we need to connect them somehow. We’ll do that with BlendSrf command which will basically create nice blend surface between two surfaces: (Use AutoConnect option in command line)

Image 10

With Join command join the blend surface with two flat surfaces. You will notice on the part where would handle start there is some weird hole. Never mind that, that part will soon disappear.

Again, we need to create another Ellipsoid. Using Ellipsoid command create one like on the image below. Again, the positioning and size is crucial here.

Image 11

Hint: When you start Ellipsoid command, just follow these steps. Input “10, -3.75″ (that will set the center in the right position), press enter while active Front viewport (click anywhere in the viewport), “6, -3.75″ (that will set one dimension of the ellipsoid – length), press enter while still in Front viewport, “10, -2.25″, press enter while in Front viewport, “10,-1.5″ press enter Top viewport is active. Do not input apostrophe signs.

Using ExtractIsoCurve command, create a extract isocurve from the middle of ellipsoid. You need to hit the Quad point to make sure the circle is in ellipsoid’s center.

Image 12

Using ExtrudeCrv command we will create a cylinder out of this circle. So, start the command, select the circle, make sure the Cap option is set to Yes, and input 15 units in command line as extrusion distance.

Image 13

With BooleanUnion command connect ellipsoid with cylinder:

Image 14

Again, with BooleanUnion command we need to connect the plate and handle part:

Image 15

If you are getting something like on the image below….

Image 16

… then you need to use Dir command on the plate before you use BooleanUnion. Because the normals are pointing towards the inside, while they should point towards outside.

This next part will be a bit tricky, so pay attention. We need to create a variable fillet on the edges that connect the handle part and the shovel plate. The biggest radius will be 1 unit, while all others will be 0.8 units.

So, start FilletEdge command, and set 0.08 as default radius. Select the edges:

Image 17

… press enter, and click on AddHandle option in command line. Add 7 more handles like on the image below:

Image 18

The two big ones show be set to 1 unit, and you do that by clicking on the outer dot (center of an arc) and inputing the values.

Image 19

Final rendered model of our windup clock

When approaching modeling this clock, and any other model, I first try to divide it into parts. Obviously every product has its parts, and naturally you would go model one by one. This is that kind of model where your don’t have to think about which part to model first. This is obvious, first you need a clock body, then you can go about modeling which ever part. Here I first created the body, then the back plate with screws, then the front plate without numbers, bells and hammer, legs, and then in the end made the numbers and handles for the front plate.

STEP 1

Ok, in this step we will be creating the body. Since I lost every clock I had like this, I had to model it from reference images from the internet. So, we don’t have the measures, or technical drawings, but we need to model by eye, looking at the various images and approximate the lengths, distances and so on.

I created a template for my default usage with grid extents set to 10. So, make sure you do the same with Snap command, and clicking on the Extents options and input 10.

Now, we can start modeling. Since we don’t know what the accurate dimensions are, we will need to use our old method of trial and error. We will first create three straight lines with Polyline or Line command.

img1

Next thing would be to connect these lines with curves, and that we will do with BlendCrv command. Make sure you use G1 for both ends, so we get tangency.

img2

Using Join command make sure those lines are all joined together. So, next thing would be to create a surface out of this section curve, and we’ll do that with Revolve command. But, before that, we need to turn on the Record History option, so we can work on the surface by simply editing the curve.

img3

Now, if we select our initial curve, and using PointsOn command turn on the control points and if we move those points, we will automatically update the surface as well. If we used Record History that is.

img4

Ok, next thing would be to adjust the curves a bit so the surface is little more accurate. Try to make something like on the image below:

img5

Using OffsetSrf command, we need to offset this surface to inside by 0.3 units. So, make sure you flip the direction normals when in OffsetSrf command, so they point to inside.

img6

Then, simply, with BlendSrf command blend the gaps and Join the four surfaces.

img7

Final scene

Since it that time in the year again, some of you might find it useful to learn how to create few Christmas decorations for your tree visualisations

Introduction

Well, basically what we will do here is use solids for basic shapes and cut them how we like it.Simple, eh?

Step 1

In this step we will be creating the simplest decoration.

First Decoration

Go ahead, and create a sphere using Sphere command. Center it in the origin (0,0) and use 10 units as radius. To make this even simpler, you can set your Grid options like I have them. Just run Grid command, and where it says Extents click on it and input 10. That way you will have 10 units in your grid in every direction in the viewport which was active when you run the command. To apply this setting to all viewports, just use ApplyTo setting in Grid command. Click on it so it toggles from ActiveViewport to AllViewports. Now, simply using Snap option in your status bar we will start creating this Sphere.

Image 1

Once you got your Sphere, create another one, using 7 units as radius and position its center on 8,0. That is, 8 on the x axis, and 0 on the y axis.

Image 2

Now, using BooleanDifference make a hole in the bigger Sphere.

Image 3

We need to fillet the edges of this sphere. Using FilletEdge command fillet the edge with 0.2 as radius.

Image 4

Create a Circle from Top viewport with 5.5 as radius.

Image 5

We will Project this Circle onto the Sphere. We need to do this from Top viewport. So make sure it is active, and run the Project command to do the projection of the Circle on the Sphere. You will get 3 projected curves, and we only need the top one, so you can delete other two:

Image 6

Using Split or Trim command, we need to trim the upper part of the Sphere, with projected circle.

Image 7

Next thing we need is another Circle. This time create a Circle with 1.5 units as radius. Create it from top viewport in the origin (0,0). Then you will need to move it up (from either front or right viewport) with Move command by 17 units.

Image 8

Now, using ExtrudeCrv extrude this circle up by 1 unit. Make sure you don’t have Cap set to Yes, or BothSides set to Yes. Those two options need to be set to No.

Image 9

Ok, once you’ve done this, you need to make a surface with smooth transition from the sphere to the extruded circle. You will use BlendSrf command to do just that. As for the BlendSrf options, just leave it at default settings. Meaning AutoChain set to No, and for the Blend Bulge leave it as well at default settings, which are 1,1 and all other options unchecked.

Image 10

Next we will create a cap and a little wire to hang our decoration somewhere. So, using OffsetSrf offset the little cylinder surface outwards by 0.1 units.

Image 11

Now, using ExtendSrf command we will extend the upper edge of the offset surface up by 0.1

Image 12

Using Cap command we will close this surface into solid.

Image 13

Create another Circle, from Top viewport and use 0.5 units as radius. You should get your circle like on the image below:

Image 14

Now, using ExtrudeCrv command set the Cap setting to Yes, and extrude it up by 20 units, just so it goes through the cap:

Image 15

Using BooleanDifference command make a hole with this cylinder in the cap:

Image 16

Using FilletEdge fillet the edges of the tip with 0.1 as radius:

Image 17

Create another Circle with 2 units as radius, and position it like on the image below. Just make sure you create your circle from Front viewport. You can start Circle command, input in the command line when it asks you for the center 0,20 for the center, and then just 2 for the radius. You should get exactly the curve like on the image:

Image 18

We need a Curve starting from the circle. Using InterpCrv command we will create such curve from Front viewport: (you can start using OSnap if you haven’t already – Near would come in handy here)

Image 19

Using Mirror command we need to mirror this curve to the other side.

Image 20

Using Trim command we need to trim the Circle:

Image 21

I have almost perfectly hit the curve direction and smoothness and actually the curve is visually tangent to the circle. In reality that isn’t the case, so we need to fix it. We will match our curve onto the circle with Match command:

Image 22

Here you can see the black curve on the left, this is how the curve will be adjusted to match the tangency. So, now you see I didn’t actually hit the tangency manually. Do this same step for the right curve as well, and join all three into one:

Image 23

If necessary, using PointsOn you can change your curve a bit. But you will see if this is necessary after you make a surface. Using Pipe command we need to create a pipe surface. Use 0.2 as radius:

Image 24

Here you see this needs some adjustments. So, first, try moving it up a bit to see if this can fix it. If not, using PointsOn you will need to adjust the curve itself.

Image 25

For the purposes of this course, just moving this wire will do.

INTRODUCTION

Ok, this tutorial is pretty simple modeling wise, and probably doesn’t bring you anything newer than the previous tutorials, but none the less it is a good practice. Again, in this tutorial we’re not designing but rather just sharpening our modeling skills in Rhino. And by wide range of different models to model through these tutorials, you just simply learn to model. So, lets begin with this one.

This is the model you will create:

Final

STEP 1

We will start out from Top viewport with couple of Circles. It is always good practice to start modeling your model from origin. Usually things are symmetric and this way you are able to control your model even more, not to mention model one half if the other is the same.

Go ahead, and create two Circles with Circle command using 12 units and 8.75 as radii.

img1

Then you need to move the smaller Circle up on the Z axis by 4 units. Do it either from Front or Right viewport.

img2

Now, you need to Copy that Circle and move it up by 44.5 units.

img3

Using ExtrudeCrv command, and with Cap option set to YES, you should extrude bottom (bigger) circle up by 4 units. To do that without measuring and typing in the command prompt the values, you could easily just use Object Snap (OSnap) with Near option turned on.

tap4

Do the same for the smaller circle. Using the bottom one extrude it, all the way up to the upper one.

img5

Now, with Point command, create a point from Front viewport with x,y as -18,31 (x=-18, y=31).

From that Point, working in Right viewport create another Circle with radius of 8.45. If you turn on the OSnap “Point” option you will snap with center on the point.

img6

Using that Circle, we will create another extrusion. Using ExtrudeCrv command again we will extrude that Circle by 18 units. Just to the y axis.

img7

Using BooleanUnion command, join the three surfaces to form one. Then with FilletEdge command, you will create filleted edge.

img8

Ok, before you go and create a FilletEdge with default 1 unit as radius, you just need to start the command and select the edge like on the image above. Now, click on the AddHandle option to add handles. We are not going to have the same radius. We are going to have 4 handles, where we already have one. So using Quad OSnap option (it would be good to turn off the others) we will add 3 more handles on quad sections. Then, clicking on the handles dots you can input the radius for each one. So, for the upper and lower we will set 0.5, and left and right 2 units.

img9

img10

Again, using FilletEdge fillet the edges like on the image below (use 0.2 as radius):

img11

Now we will create two more circles. You can use the existing one to Copy it and make two more instances 0.8 units and 10.3 units left of the original circle looking from the top viewport.

img12

Using the same original circle like on the image above, we will Offset it by 2 units inwards.

img13

We will extrude that offset circle by -3.8 (the minus sign means it will extrude to the left, rather than the default right – towards positive).

img14

Using BooleanUnion join that cylinder with the rest of the tap body. Now, using FilletEdge and 0.2 as fillet radius fillet the edges like on the image below:

img15

Using the two single circles we created earlier, make a solid with ExtrudeCrv command:

img16

Now, isolate the cylinder you just created and the circles on the edges of that cylinder. You can use Hide and UnHide commands, or just use Layers and put them in different layers. Either way you need to isolate your objects you’re working on.

img17

Using Offset command again, we will offset the Circle which is near the tap body. The right one looking from Front viewport. The offset distance will be 1.2 units towards inside.

img18

Using Split command we will split the cylinder object with inner circle. Then the surface which is left inside the circle needs to be moved by 2 units left looking from Front viewport.

img19

Now, using Loft command we will fill in the gap between the surfaces.

img20

Join all surfaces and using FilletEdge with 0.2 as radius fillet these edges:

img21

When you unhide everything, you should have something like this:

img22

Now, we will edit a little this cylinder we worked on. Using MoveFace we will move left face of it like on the image below. The distance is not very important:

img23

If you done all the measurements like I stated, then you should make a Point next. From any viewport this time, because we will define all three axis values. So, go make a Point with -26.35,0,74 (x,y,z).

After you’ve done the point, copy it using Copy command and move it down by 31.5 units:

img24

Next we need another Circle. This time with a radius of 1.7 units, and a center in the lower point. You can easily do that by starting the Circle command then snapping to the point (use OSnap Point option) and clicking to set the center of the circle, then move to Top viewport (make it active) and input 1.7 units as radius.

img25

Do the same for the upper Point, but create a circle there with radius of 2 units.

img26

INTRODUCTION

I really liked modeling this model, it turned out really good, and I must say that it was pretty easy to model it too. However, there is fairly enough playing with Osnap, but then again, when do we not use Osnap frequently? Anyway, to get you started, you first need to download some kind of blueprints I made for you out of this model. You just gotta love that Make2D command!!!

Blueprints reference

STEP 1

First things first, we need to setup our blueprints. Not only import them into Rhino, but also position and scale to fit the dimensions marked on them. First, go to Front viewport. You can expand it by double clicking it. Next, using PictureFrame command browse for blueprints you previously saved to your computer. Now, you don’t need to worry about how to position or how big you should make it. We will fix that in a bit, but just make sure your blueprints are not tilted. For that you can use Snap, or even better Ortho.

PictureFrame

Move from blade tip

Scaled blueprints to fit the line length

Another line

pic

STEP 1

Ok, we will cut to the chase straight away. We’ll start this one off with making holes for windows and doors. So, using Rectangle command, just outline the windows and doors.

image 1

You can actually use the curves from the plans, it might even speed up this process, but I like it this way. After you’ve created all the rectangles needed, we will next create holes with MakeHole command.

image 2

Once you’ve done that (I’ll do the roof windows later) we need to create the windows and doors to fill those holes we just made. So, if you haven’t already, outline other lines on the windows plans. For each window or door we need 3 sets of rectangles. We already have one set. Then we will use outer 2 and using ExtrudeCrv command we will extrude by 1 unit with Cap set to Yes.

image 3

Then, repeat the ExtrudeCrv command with inner two rectangles.

image 4

Then, using PlanarSrf, just create surface out of inner Rectangle.And move the middle extruded part towards inside by 0.5.

image 5

To make it a bit more realistic, you can fillet the edges with FilletEdge command and 0.1 as radius.

image 6

Now, we’ll need to position this window. Move it towards the inside of wall by 0.5.

image 7

The process for the doors and other windows is pretty much the same. Copy the objects that are the same and you already modeled them, and model the other windows and doors.

image 8

Now, let me go back to the roof windows. The problem here is the windows are tilted under certain degree. This way it is pretty hard to model, because everything then is defined by that degree. But thankfully,  since Rhino is such great tool, it lets us adjust CPanel (construction panel) so that the cp is tilted, and when we model on such cpanel, then everything else is normal, modeling wise.

Lets first create some more Rectangles for the windows outlines. After that, just Project the rectangles onto the roof (do that from either front or back viewport because that is the projection direction we need).

image 9

We will set the CPlane orientation, so from Perspective view select one projected rectangle and right click on the “Perspective” name in the viewport, and select Set CPlane->To Object.

image 10

Now it is fairly easy to do anything with this rectangle. So, lets first create the set of 3 rectangles for each window we need. Offset each Rectangle to the inside first by 1 unit, then by 0.5. And using MakeHole we will create holes for the windows:

image 11

Using the same method we used for the other windows, we will create these roof windows.

image 12

For the balconies detailes, I believe you can figure that out on your own. If not, let me know, I’ll explain. Basically all you need is to create Box with 1×1 base, and height the same as on the plans.

Anyway, I hope this was helpful.

INTRODUCTION

Ok, this is another tutorial on modeling some ID product. I’ve tried to simplify this to the bare bone, and I hope I managed to do it. Actually, this is a method you could use on various other projects too. This is what it all comes down to, all you need is create a set of base curves right, after that it is all just music to the ears.

STEP 1 – creating the curves

In the images in this tutorial, you will notice I have 20×20 grid system. You can take a look at my previous tutorial on setting up and prettifying user experience by changing grid and other settings. That will give you an idea how to change your grid system. Basically it is just grid option Extents that is set to 10.

To start off, we will need 4 points. We will use those 4 points for creating a curve. So, go ahead and maximize your Front viewport and create 4 points with x and y coordinates as set: x=-17, y=1 / x=-5, y=-1 / x=9, y=-2 / x=22, y=-1.

create 4 points

Using Curve command, create a curve between those 4 points. To make it easier to snap to the points, just use Osnap option Point. Next, create a line horizontal with start at -17,2 and end at 22,2. We’ll need one more line with start at 7,3 and ending at 8,4. You can create them with Line command or just PolyLine.

two more lines

Next we will create one polyline and one line from Right viewport. Use PolyLine command and for 4 points of polyline use: -4,-5 / -2,-10 / 2,-10 / 4,-5. For the line use PolyLine or Line command and for the start and end use: -5,-8 / 5,-8.

creating some more lines

Using Trim command, just trim off polyline and line, leaving everything above the line. Once you do that, using PointsOn command, you simply show control points of two tilted lines and move the upper control points up by 1 unit.

trim and move control points

In perspective viewport Move (or Copy) that polyline from Mid of the middle (straight) line, and move it to the end point of the first curve we created (22,-1).

moving polyline

Go to Top viewport, and from there create a curve with Curve command (-4,10 / -10,0 / -4,-10).Note, it would be smart to disable Osnap for a second when you are creating this curve. You might get in trouble at middle point if you have some Osnap options on, so to avoid any possible problem, just disable osnap for this step.

just another curve

Move that curve 6 units left. So it just touches the grid. From front viewport move it up by couple of units i.e. 5. Using Rotate command and clicking on the Copy option in command line we will create one more instance of the curve but rotated by 90 degrees. Then, if you haven’t already, enable Osnap, and using Mid option move that curve to the first point of our first curve (-17,1). Use Osnap option Point to snap to that point. Otherwise if you want to input the coordinates, you would have to do it from the same viewport where you created that point, so from Front viewport.

Rotate & copy, move

Ok, this step might get a little confusing, so pay attention. We need to set that curve to face the curve perpendicular. Check the image to see what curves I’m talking about:

what to do

Now, we need to rotate vertical curve so it is perpendicular to the bottom curve. We’ll do that by first creating a line that is perpendicular to the curve below. So, start your beloved PolyLine command, and hover your mouse over the Osnap options, and while holding down CTRL key, you will reveal some more Osnap options. Click on the second one, PerpFrom. Now, you are asked to select the curve on which you would like to show the tracking, so select the lower curve. Now, you can move the tracker where you want to start your line from, and move it all the way to the left (Point Osnap option might help, or end).

PerpFrom osnap option

Now, we created a line that we will use for a rotation angle.

line

Now, just rotate from Front viewport the curve to fit the line angle.

rotation

Now, repeat this step for the other end of the curve and other section polyline:

repeat for this side as well

Introduction

So like I said, in this tutorial you will learn how to model a light bulb in Rhino. The first “glass” part will be just a bit tricky because we need to control the curves little bit more than usual. After that we will make bulb screw threads, where the method is similar if not the same as the one explained on Rhino tips website. If only I known for it when I made this tutorial heh. Anyway, this one is pretty easy, but needs some special attention in some parts.

If you like, you can download source 3dm files step by step just to keep on the track.

source 3dm files step by step

This is what you will have in the end:

final model

STEP 1

First we will start from top to bottom. So we’re making the lighting spiral. Start with creating Circle from top view of radius 5cm. And create two small circles of radius 1cm. You can use Snap to make them really easy:

image 1

Next, we need a Spiral. Using Spiral command make one starting from origin. Once you start the Spiral command just input 0 (zero) and press enter, now from Front viewport make it high 5cm. And for the radius use your already made circle that is 5cm in radius. Move that spiral 3cm up from front viewport and you should get something like on the image 2 and image 3.

image 2

image 3

Now we need a little help line. You can make one starting from center of the right smaller circle. It should be straight vertical line, so you can finish it either from front or right viewport:

image 4

Now, using BlendCrv blend the lower end of spiral to the little help line with G1 continuity on both sides:

image 5

Using Copy command, copy the spiral and blended curve. While in the Copy command in the command line click on InPlace option. Or simply use Copy & Paste commands (ctrl+c, ctrl+v). While having selected two copied curves, Rotate them from top viewport by 180 degrees. Check if you have something like on the image 6:

image 6

Now, with create a Point from right viewport (or front would work fine too) exactly 9cm from origin:

image 7

Now, start Extend command, and press enter for dynamic extend. Enable OSnap and check Point option, and click on each upper end of spiral and extend it to the point.

image 8

Now the endings of two spirals are not tangent. So with Match command we will match those two curves. Make sure both ends are set to Tangency and Average Curves is checked:

image 9

Now select all 4 parts of 2 spirals and join them together. Now, using Pipe command we will make a surface out of this curve. For the starting and ending radius you can use two small circles as reference. Near OSnap option is a good way for this. Ofcourse, you could use sweep1 or even sweep2 commands.

image 10

Now the big circle will be used to create the body of our bulb. Select it and run ExtrudeCrv command. Make sure the Cap is set to Yes and BothSides to No. We will extrude it down by 8cm, so you can either use snap and count for yourself, or simply input in the command line -8 and press enter.

image 11

Using FilletEdge command fillet the upper edge of the cilinder by 0.5cm.

image 12

Using one of two smaller circles offset one by 0.3cm. And move it up vertically by 0.6cm.

image 13

Using Rib command and the body of the bulb create a surface like on the image 14. Rib distance is 0.2:

image 14 - mirrored curve for rib

Now for the ribs, we can make them look even prettier by filleting edges. So with FilletEdge command fillet those three edges for each rib with 0.05cm as radius:

image 15 - filleting

Now lets get back to the lower part of the bulb body. Like we filleted upper edge, we will chamfer the lower one with ChamferEdge command using 2cm as CurrentChamferDistance option.

image 16 - chamferedge

Now, we will FilletEdge the middle edge with 0.5cm as fillet radius.

image 17 - filletedge radius 0.5cm

Using ExtractSrf command we will extract the bottom cap surface:

image 18 - omg, we're using ExtractSrf for the first time

When you extract this surface, you can delete it. And using the edge where this surface was extrude it by 1cm down. So just input in command line when extruding -0.5. Make sure the Cap option is set to No.

image 19

Now, you can create PlanarSrf to “cap” it on one side: (you could also join all the upper surfaces of this bulb body and simply use Cap command to close it)

image 20

Lets do some details on the body. From front viewport create one line and offset it down by 0.3cm… Like on the image 21

image 21

With Trim command trim the body surface between two lines:

image 22

Using Offset command, offset the two edges inwards by 0.2cm. The easiest way is to first have everything deselected and run the command offset, then click on one edge from perspective view, and then from top viewport simply move your mouse pointer inside the cilinder and in command line type in 0.2 and press enter. Do the same for the other edge and you are set to go.

Then, using Loft command click on the lower edge first, then two offset circles inside, and then the upper edge, and with style set to Straight sections create loft:

image 23

Now, join those surface, and make it prettier with FilletEdge using 0.05cm as radius.

image 24 - smooth edges with FilletEdge

Ok, first things first. We need reference image which will help us model this little bugger. So, please use this one, and position it on the background of Top viewport. Make it 40 units (make sure you’ve got your Snap turned on) in width.  Like so:

STEP 1

Then using Rectangle command create one rectangle like on the image (please note, if you followed the above intructions then you will have absolutely no problem aligning with using snap rectangle corners according to the image)

You can explode that rectangle into 4 lines with explode command, and then offset upper and lower ones by 2 units towards inside:

Now, create an Arc using Mid Osnap option  and position it like on the image. (you will have to turn off the snap option, and turn on the Ortho for moving the arc straight). After that trim off the lines you don’t need with Trim command.

Ok, lets get to the third dimension now Join all curves and lines, and extrude them with ExtrudeCrv command (make sure you have Cap set to yes). Extrusion distance is 5units:

Now, offset joint curve by 0.5 units, and move that offset curve upwards (from Front or Right viewport) by 0.5 units, and extrude it by 4 units.

Using FilletEdge command, set the fillet radius to 0.6 units, and fillet all edges (of both outer and inner objects).

Now, using Rectangle command (make sure you click on Rounded in Rectangle options before setting first corner) create rounded rectangle in Top viewport and position it like on the image below:

Copy it 5 times, and mirror those 5 so you get something like on the next image:

Using Project command, project those curves on both objects:

Trim the upper surface with upper curves like on the image, and inner curves with inner surface:

You’ll have to end up with something like this:

Now, isolate two curves like on the image. We will create surface between those two.

As you can see, there are actually couple of lines and couple of arcs combining these two curves. So, at each intersection of lines and curves, there is an end. So, using End Osnap option, and Perp we will create cross section lines.

Now, using Sweep2 create a surface using two curves as rails, and other cross lines as cross sections:

Copy and mirror to fill the rest of the gaps:

Join all surfaces, and using FilletEdge command fillet new edges (do not worry, you can select everything with your bounding box, as there is no other edge that can be filleted except the ones we need ) . Use 0.1 units as filet radius.

Ok, first, sorry for delay, I’ve been meaning to write this one down for 4 days now.

I must say that I’m pretty happy with this one, it turned out very accurate and great. I really like it! And it is pretty easy to model it. So check it out:

RESOURCES

1042008419.jpg

STEP 1

Ok, first things first, so lets start with tubular part. The part where the motor and heater is. I’ve measured 120mm the length and make a line with Polyline or Line command (the length of our reference image is 190mm). We will make three circles two on the start and end of line, and one 30 or 40mm from the left circle. You need to offset them by 2mm, or simply make another circle. I made another circle, so in the end I ended up with 6 circles. Far two right circles are in radius 26 and 28mm. The far left two are 34 and 36mm, and the inner two are 35 and 37mm.

Using InterpCrv command make a line connecting three outer circles. (use Quad option in Osnap for easier snapping). Next, do the same step for 3 inner circles.

Using Sweep2 for first and second rail select outer two circles, and for cross section curve select Curve we made earlier.

Make an ellipse and position it like on the image below:

Next, from Front viewport use Project command to project that ellipse onto our tubular surface. You will get two curves on the surface, and we need only the front one. Using it, we will trim the surface and make a hole:

Now, we’ll move onto handle. I like jumping from one part to another, I guess you already found that out

From top viewport using reference image, outline outer edges with InterpCrv. Just to make sure, I made a straight horizontal line in Top viewport (using Ortho) and trimmed off the two curves. Now, we are sure those two curves has endings in the same cplane.

Create another ellipse, this time one radius 15mm and other 13mm. Using End and Quad options in Osnap, position the ellipse between two curves, first move it to the end of one curve, and using PointsOn command, stretch the ellipse to fit the other curve’s end.

Copy that ellipse, and position it like on the image below. You also need to stretch it with moving control points so it touches both curves. I have also made this ellipse 4 points higher. So, select upper three control points and move them 4 units up, and then move lower three control points and move them by 4 units (mm) down.

Next, using that second bigger ellipsoid and two handle curves, we will make a sweep2.

Using DupBorder we will duplicate border of newly created surface. We will get two closed curves, and we need the little one only, as we already have the bigger one. So, now, delete the surface, and again create sweep2 rail between two rail curves, and using now three closed curves:

And now, we have a handle! Next, we will blend the two surfaces, so use BlendSrf command. Note that we need to check the Same height shapes option:

Hopefully you got something like on the image below: